G&G Ingenieros offers the best solution adapted to your agitation and mixing problem.
G&G Ingenieros offers the solution that best suits for wine agitators for medium and small volumes, using side entry agitators.
Wine agitators with own design of the equipment for the most suitable agitation to the process.
G&G Ingenieros offers the best solution adapted to your problem of agitation and mixing of medium and small volumes, using side mounted agitators.
G&G Ingenieros recommends small speeds below 400 rpm for this type of agitator. The jet of fluid produced maintains some speeds and a G&G agitator came penetration higher than the corresponding jet of smaller diameter and higher speed with the same flow in both. In addition, the fluid is sheared less, which is very important for the wine.
These wine agitators are lightweight and compact so they are supported only by the flange without the need to use external supports and with enough flange to be mounted directly.
These wine agitators are made up of a motor reducer, mooring flange, mechanical seal and shaft with the propeller. All in stainless steel AISI-316L with 2B polished finish.
This type of agitators are of great application where it is required to agitate relatively large volumes of liquid with a need for medium or gentle agitation. Milk and wine agitations for temperature homogenization are typical.
Gearmotors
The selected gearmotors are of proven quality. They are well established throughout the world, providing complete technical assistance.
The motors used are at least IP55 protection and insulation class F.
The gearboxes used are hollow shafts that allow the agitator shaft to be fixed at the rear by removing the cover. This makes it very easy to assemble and disassemble.
The service factor of the reducers is always higher than 2. This translates into great reliability and durability of the equipment.
Mechanical seals
The sealing of the shafts is by mechanical seal. The mechanical seals are specifically designed to work with the fluids handled and are of recognized brands.
The flange has a witness of mechanical seal breakage providing reliability to these agitators.
Thin profile propeller
The performance of the agitator depends on the design of the impeller and its efficiency. The thin-profile propeller in its PD10 specialisation offers unbeatable flow characteristics, with very little loss from turbulent energy.
It is a highly efficient propeller for the displacement of liquids that makes it ideal for equipping the side entry agitators.
The range of agitators goes from 0.12 kW the smallest to 5.5 kW the largest, covering from 10m3 to 850m3.
Side agitators for WINE HOMOGENIZATION
Application
This type of agitators are of great application where it is required to agitate relatively large volumes of liquid with a need for medium or gentle agitation. Milk and wine agitations for temperature homogenization are typical.
Assembly
In order to avoid that the liquid acquires a rotary movement of set that is pernicious since it does not contribute vertical flows for what it generates stratification and also generates pernicious efforts on the deposit, it must be placed with an angle with the corresponding radius of 7-10º in the horizontal plane.
The inclination in the vertical plane Bº depends on the ratio of liquid height to tank diameter. In order to be able to guarantee the power supply circuit of the mobile also has to be to a minimum separation of the wall of the deposit that normally has to be ≥ D. For the same reason H≥ D.
If the installation so requires, a sufficiently large clamping flange can be provided to allow the propeller to pass through the neck of the tank and therefore to fix the previously mounted agitator.
Other recommended products
TOP-ENTRY AGITATORS VPD/VTA
Top-entry agitators with own design of the equipment for the most suitable agitation to the process.
Read more
SIDE-ENTRY AGITATORS HPD
Side-entry agitators with own design of the equipment for the most suitable agitation to the process.
Read more
PORTABLE AGITATORS
As mobile industrial agitator manufacturers, two important parameters must be taken into account, such as the characteristics of the various products and their continents on the one...
Read more
DIRECT-DRIVE AGITATORS
Direct-drive agitators with own design of the equipment for the most suitable agitation to the process.
Read more